Bitcomet 1.29, Windows XP sp3 32 bit
Dell Inspiron 6000
Intel Proset Wireless 2200BG
Router N-Max LevelOne WBR-6020
Server: Intelnet.gt
TCP optimizer at 512 Kbps
Need assistance with setting up router to open BitComet WAN TCP Port. Have LevelOne WBR-6020 Users Manual but can be a little confusing…to a novice
Where exactly are you running into problems?
Cannot get WAN TCP open. Have tried forwarding ports in router using LAN IP and then using WAN IP…no luck…tried DMZ … no luck…also tried disabling NAT but its a little confusing because it shows:
NAT disable _____ Enable (this is a check box option)
which means place a check mark in the enable box to Enable the NAT disable? OR Enable the NAT? Also found that I am a DHCP client to the DD-WRT listed below which leads me to ask if its ports need to be forwarded?
Router System Information
Router Name DD-WRT
Router Model WHR-HP-G300N
LAN MAC 00:24:A5:B4:26:87
WAN MAC 00:24:A5:B4:26:87
Wireless MAC 00:24:A5:B4:26:87
WAN IP 192.168.1.15
LAN IP 192.168.0.1
SSID
The … NET
Channel
11 (2462 MHz)
TX Power
13 dBm
Rate
108 Mb/s
Wireless Packet Info
Received (RX)
6303191 OK, 12056 errors
Transmitted (TX)
8497888 OK, 21 errors
Services
DHCP Server
Enabled
WRT-radauth
Disabled
Sputnik Agent
Disabled
Wireless Clients
MAC Address Interface Uptime TX Rate RX Rate Signal Noise SNR Signal Quality
xx:xx:xx:xx:96:45 ath0 1 day, 9:41:01 104M 54M -73 -111 38
25%
xx:xx:xx:xx:c7:60 ath0 1 day, 9:40:51 1M 104M -111 -111 0
0%
xx:xx:xx:xx:0c:d8 ath0 1 day, 9:39:00 104M 1M -78 -111 33
19%
xx:xx:xx:xx:d6:20 ath0 7:13:34 54M 18M -74 -111 37
24%
xx:xx:xx:xx:62:01 ath0 4:17:52 104M 104M -96 -111 15
0%
DHCP
DHCP Clients
Host Name IP Address MAC Address Client Lease Time
********* 192.168.0.xxx xx:xx:xx:xx:37:08 1 day 00:00:00
******** 192.168.0.xxx xx:xx:xx:xx:1D:39 1 day 00:00:00
******** 192.168.0.xxx xx:xx:xx:xx:30:DA 1 day 00:00:00
*********** 192.168.0.xxx xx:xx:xx:xx:98:FA 1 day 00:00:00
******** 192.168.0.xxx xx:xx:xx:xx:C5:89 1 day 00:00:00
********* 192.168.0.xxx xx:xx:xx:xx:50:14 1 day 00:00:00
******** 192.168.0.xxx xx:xx:xx:xx:C5:89 1 day 00:00:00
Firmware: DD-WRT v24SP2-MULTI (05/28/10) std
Time: 07:42:39 up 1 day, 9:41, load average: 0.00, 0.00, 0.00
WAN IP: 192.168.1.15
This is my Router Stats:
ADMINISTRATOR’s MAIN MENU
Item WAN Status Sidenote
Remaining Lease Time 21:48:04
IP Address 192.168.0.1xx
Subnet Mask 255.255.255.x
Gateway 192.168.0.1
Domain Name Server 192.168.0.1 , 0.0.0.0
MAC Address 00:12:F0:01:50:xx
Wireless Status
Item WLAN Status Sidenote
Wireless mode Enable
Operation Mode AP mode (B/G/N Mixed)
SSID xxxxxxxx
Channel Auto
Security None
MAC Address 00:11:6B:2D:72:xx
Statistics Information
Statistics of WAN Inbound Outbound
Bytes 2628404784 145702111
Unicast packets 1998687 1377606
Non-unicast packets 0 0
Device Time: 2011/12/18 00:53:57
If you have a private WAN address this means you are behind another NAT router.
That’s why we ask users to not waste our time and give ALL the information required in the “Read This Before Posting” announcement on top of the section.
If you would provided all the details (modem type and/or Internet connection type) we would have know that already.
Anyway, the guide I linked you to, provides guidelines for people who have daisy-chained routers, as well.
Just give it another read.
Thanks for your quick response and excuse the fact that I did not include ALL the info the first time …only because I did not have that info available as your answer suggests about a private WAN and another Router. If that info was available to me at the time of my posting I would have included it as well. I did read the link and am still working on it…